AUD · Audio tools

Multiband Distortion

Shareable link

Settings are written to the URL as you change them. Nothing differs from the defaults yet.

Oxyd To put the result on a track with other audio, Oxyd is a multitrack editor with the same effects. Open Oxyd

Drive each part of the spectrum separately. Two crossovers split the signal into lows, mids and highs, each band goes through its own distortion at its own drive, and the three are summed back together.

Why split first

A distortion stage reacts to the loudest thing it is given, and in a full mix that is the bass. Run a mix through a single-band distortion and the kick drum decides when the guitars grind. Split the mix first and each band is driven by its own content: the lows can be left clean so the bottom stays tight, the mids pushed so the body of the mix gets its edge, and the highs driven lightly so the cymbals do not turn to sand.

The same split is what lets a bass guitar be distorted without losing its fundamental: keep Low drive near 0, push Mid drive, and the growl sits on top of a bass that still has weight.

Crossovers

Low split runs from 40 Hz to 500 Hz, High split from 800 Hz to 8 kHz. Each split is a fourth-order Linkwitz-Riley crossover: 24 dB per octave on both sides, summing to a flat response. The steepness matters here more than it does in a compressor. A gentler crossover leaves a 60 Hz tone leaking into the mid band at -7 dB, and a drive on the mids would then distort the bass it was meant to leave alone; at 24 dB per octave the same leak is -42 dB. The high split is held at least one and a half times the low split so the mid band cannot be pushed out of existence.

Drive per band

Each band’s drive is measured against that band’s own running level, so Drive means the same thing whether the band is carrying a kick drum or a hi-hat. At 0 the band passes untouched. Around 40 the peaks round off audibly. At 100 the curve is driven thirty times over and the band is a wall of harmonics.

Characters

Character What it does Harmonics
Soft clip Rounds the peaks Odd, growing smoothly with drive
Hard clip Flattens the peaks Odd, sharper
Foldback Reflects anything past the limit back toward zero Dense and inharmonic
Tube Bends around an operating point off centre, like a single-ended stage Even as well as odd

A curve that is symmetric about zero gives only odd harmonics however it is shaped, because driven hard it becomes a square wave. The tube curve sits the signal at an operating point off centre, the way a single-ended valve stage does, so the zero crossings move and even harmonics appear, and they stay as the drive rises. The bias leaves a little DC behind, which a one-pole high-pass at 8 Hz removes before the bands are summed.

Aliasing

A curve applied at the source rate creates harmonics above the file’s Nyquist frequency, and those fold back as tones that have nothing to do with the music. Each band’s curve runs four times oversampled with a filter either side, so what would have folded is removed before it can. The filters add 16 samples of delay, declared to the runtime: the dry half of the mix is held back to match and the export is trimmed.

Pairing

The multiband compressor splits at the same two frequencies; a compressor before this stage evens out the level each band’s drive sees. The limiter after it catches the peaks the summed bands can add up to.

Frequently Asked Questions

It splits the audio into three bands at two crossover frequencies you set, runs each band through its own distortion with its own drive, and sums them back. A band at drive 0 passes clean. Lows, mids and highs can be driven differently, which a single-band distortion cannot do. It reads WAV, MP3, M4A, AAC, Ogg, Opus, FLAC, AIFF and WebM audio.

A single-band distortion driven by a full mix is driven by its bass. The kick sets the level the curve sees, so the mids and highs only grind when the kick lands and the whole thing pumps. Splitting first lets each band be driven by its own level, so the mids can bite on every note while the low end stays intact.

Its own running level, over about 20 ms attack and 800 ms release. A band 20 dB quieter than another gets the same amount of bend at the same drive setting. Drive is how hard the curve is pushed, not a gain control in disguise.

Soft clip rounds the peaks and adds odd harmonics that grow smoothly with drive. Hard clip flattens them and adds a sharper set. Foldback reflects anything past the limit back toward zero, which turns a loud note into a buzz. Tube bends the signal around an operating point off centre, the way a single-ended valve stage does, which adds even harmonics for a thicker, less fizzy sound.

Each band's curve runs four times oversampled so the harmonics it adds above the file's Nyquist frequency are filtered out instead of folding back as tones unrelated to the music. The filters add 16 samples of delay, declared to the runtime, so the dry path is held back to match and the export is trimmed.

Explore Our Tools

Browse all tools