AUD · Audio tools

Tape Echo

Shareable link

Settings are written to the URL as you change them. Nothing differs from the defaults yet.

Oxyd To put the result on a track with other audio, Oxyd is a multitrack editor with the same effects. Open Oxyd

Repeat the signal through a machine instead of a buffer. Time and Repeats work as they do on any delay. The machine and its wear decide what each repeat loses on the way round.

What a repeat loses

A tape loop records the repeat onto tape and plays it back, and each generation loses something. Here the loop does the same three things in series: a soft saturator bends the loud peaks, a low-pass takes some treble, and a high-pass takes a little bass so the low end never piles up. The repeat you hear is the signal after one pass; the one after it has been through twice.

The saturator is what separates this from the echo page. Feed a clean delay a loud transient at high feedback and the repeats clip; feed this one the same thing and they compress and darken, the way a pushed tape blooms.

Machines

Machine Treble per repeat Wobble Saturation Extra
Tape from 7 kHz, falling with wear moderate wow at 0.6 Hz, flutter at 6.1 Hz medium hiss with wear
Bucket brigade from 3.8 kHz small, fast clock jitter light more noise floor
Oil can from 2.6 kHz wide and slow hard the darkest
12-bit digital held at 10 kHz none hard clip 12-bit quantisation

The oil can is the odd one out. Those units stored the signal electrostatically on a rotating drum running through oil, and the drum’s speed wandered more than any tape transport, which is where the seasick wobble comes from.

Wear

Wear is the age of the machine. It widens the wobble, lowers the corner of the loop’s low-pass so repeats lose treble faster, and raises the noise added on each pass. At 0 the machine is new and the repeats are as clean as that design gets. At 100 it is the one in the back of the rehearsal room.

Repeats and self-oscillation

Repeats sets the loop gain. At 0 there is one repeat. Around 45 a handful of repeats fall away. Past about 90 the loop gain reaches unity and the repeats stop decaying; the saturator holds the level, so the machine oscillates instead of running away. Lower the control again and the oscillation fades over a few seconds.

The export renders the repeats after the source ends until they fall below -60 dB, capped at 12 seconds. An oscillating loop hits the cap.

Changing the time during playback

Moving Time slides the read head, which bends the pitch the way a tape machine changing speed does. The slide is rate limited so a large jump sweeps over a couple of seconds rather than tearing. None of this reaches the export: a render starts from the settings in place and never changes them partway.

Frequently Asked Questions

The echo is a clean digital line: every repeat is the last one, quieter. Here each pass through the loop goes through a saturator, a low-pass and a high-pass, so each repeat is darker and softer than the one before and a loud one blooms instead of clipping. The read head also drifts with the machine's wow and flutter, so the repeats wander in pitch. It reads WAV, MP3, M4A, AAC, Ogg, Opus, FLAC, AIFF and WebM audio.

The losses in the loop. Tape loses treble from about 7 kHz per repeat with moderate wobble. Bucket brigade is darker still, with a faster, smaller clock jitter and more noise. Oil can is the darkest, with the widest, slowest wobble and the hardest saturation. 12-bit digital holds the top end to about 10 kHz, does not wobble at all, and quantises each repeat to 12 bits.

The loop gain goes slightly past unity, so the repeats stop fading and the saturator decides the level. The result is the self-oscillation a Space Echo makes with the repeat knob cranked, held safely rather than running away. The export caps the tail at 12 seconds, so an oscillating loop is cut there.

A high-pass inside the loop, between 40 Hz and 160 Hz depending on the machine, takes a little low end off every pass. Without it, a bass-heavy source at high feedback turns to mud within a few repeats on any real machine too.

Yes. The saturator runs oversampled and adds a third of a millisecond to the loop; that is subtracted from the delay so the first repeat lands at the time set.

Explore Our Tools

Browse all tools