AUD · Audio tools

Room Simulator

76 m³volume0.38 spredicted RT602.8 msource to listener0.8 mcritical distance

Shareable link

Settings are written to the URL as you change them. Nothing differs from the defaults yet.

Oxyd To put the result on a track with other audio, Oxyd is a multitrack editor with the same effects. Open Oxyd

Build a room from its measurements and play a recording in it. The reflections are not designed, they are computed: from the size of the room, what its surfaces absorb, and where the source and the listener are standing.

Room size

Length runs from 2 m to 30 m, width from 2 m to 20 m, height from 2 m to 10 m. Size sets two things at once. A bigger room has a longer decay for the same surfaces, and its first reflections arrive later, which is the cue the ear uses to judge how large a space is. A 3 m bathroom returns its first reflection within 5 ms; a 25 m hall takes ten times as long.

Absorption

Absorption is the share of sound each surface removes per bounce.

Surface Absorption
Bare concrete, tile 2% to 5%
Plaster, glass 5% to 10%
Furnished living room, on average 20% to 30%
Carpet and heavy curtains 40% to 50%
Treated studio 60% and up

High damping makes the top end of the decay die faster than the rest, as it does in any room with soft surfaces and air in it.

The readout

Under the waveform the page shows four figures for the room as set.

  • Volume, in cubic metres.
  • Predicted RT60, the time for the reverberation to fall by 60 dB, from Eyring’s formula.
  • Source to listener distance.
  • Critical distance, where direct and reverberant sound are equally loud. A listener closer than this hears mostly the source; one further away hears mostly the room.

Positions

Source and listener are each placed along the length and across the width, as a percentage of the room. The source stands at 1.5 m and the listener at 1.2 m, lower in a low room.

Moving them changes more than the balance. A listener 1 m from the source in a live room hears it nearly dry. Back the listener into a corner and the bass reflections pile up. Put source and listener at the same distance from a side wall and one strong early reflection colours everything, which is the comb filtering a real room does.

How the response is built

The first 80 ms are counted reflection by reflection with the image-source method, up to about 6,000 of them. After that the reflections are too many and too close together to hear one by one, so the tail is noise shaped to the decay time Eyring predicts, at the level the density of reflections predicts. The travel time of the direct sound is trimmed off so the room stays in step with the untreated file.

Impulse response

Download impulse response writes the room as set to a stereo 48 kHz, 24-bit WAV. It loads into the convolution reverb here or any convolution plug-in. Run it through the reverb time analyzer to check the room against its prediction: the measured figure should land close to the readout, a little shorter where High damping is raised.

Mix

At 100 the output is the room, direct sound included, which is what a microphone at the listener’s position would record. Lower values keep some of the untreated file on top, for when the room is wanted as an effect and not a place.

Frequently Asked Questions

It computes how a rectangular room of a given size would sound and plays the audio file inside it. You set the room's length, width and height, how absorbent its surfaces are, and the positions of the source and the listener. It reads WAV, MP3, M4A, AAC, Ogg, Opus, FLAC, AIFF and WebM audio, and the room's impulse response can be downloaded as a 24-bit WAV.

A reverb gives you a decay to shape. Here the reflections are calculated from geometry: each one arrives at the time its path length divided by the speed of sound says it should, at the level its distance and number of bounces say it should. Moving the listener towards a wall changes the pattern the way it would in the room.

A way to compute reflections in a box-shaped room, published by Allen and Berkley in 1979. A wall acts as a mirror, so each reflection is treated as direct sound from a mirror image of the source on the far side of the wall. Reflections of reflections are images of images.

From the room's volume and surface area with Eyring's formula: RT60 = 0.161 V / (-S ln(1 - a)), where a is the absorption. The predicted figure is shown under the waveform. A 6 by 4.5 by 2.8 m room at 25% absorption comes to 0.38 s.

Anything that is not an empty box. There is no furniture, no doors or windows, no angled walls, and every surface has the same absorption. The listener is two points 17 cm apart with no head between them, and decays longer than 6 s are cut at 6 s.

Explore Our Tools

Browse all tools