IMG · Images tools

Seamless Texture Maker

Shareable link

Settings are written to the URL as you change them. Nothing differs from the defaults yet.

Turn a photo of a surface into a tile that repeats without a visible join. The preview shows four copies side by side, so the seams you are removing sit in the middle of the picture where you can see them.

Fold the edges over

A photo’s left edge and right edge are different places, so putting two copies next to each other shows a line. The fix is to make them the same place. A strip is taken from the right side and laid over the left side, and the tile is cropped to end where that strip began. The pixel just past the right edge of the tile is then the first pixel of the strip, which now sits at the tile’s left edge. The same is done from bottom to top.

The Overlap slider sets the width of that strip as a share of the image. A wider strip gives the join more room to find a good route and costs more of the picture. 20% suits most surfaces. Raise it for coarse textures such as cobbles or large gravel, where a narrow strip may not contain a route between the stones.

The cut

Where the strip ends is what decides the result. A cross-fade across the whole strip shows both layers at half strength, and every pebble gains a ghost. The cut here is a single path from one side of the strip to the other. For every pixel in the strip the colour difference between the two layers is measured, and dynamic programming finds the connected path with the lowest total difference. It tends to run along the edges of stones, through shadows and across flat areas, where a change of layer cannot be seen.

Edge softness feathers that path. At 0% it is a hard line one pixel wide, which is right for crisp textures such as gravel. Higher values blend up to 2% of the image’s short side on each side of the cut, which hides the path in smooth surfaces such as plaster, skin or cloud.

The second pass, top over bottom, uses a path that ends in the column where it started. Without that constraint the vertical join would reopen the horizontal one at the corners.

Uneven lighting

A tile can join without a seam and still read as a grid. The cause is low-frequency drift: one corner slightly darker, a warm cast on one side. Even lighting estimates that drift with a blur one fifth of the image wide and subtracts it, keeping the average colour. At 100% the drift is removed completely. Lower it if the surface has real large-scale variation you want to keep, such as the grain bands in a plank.

Example: a 3000 × 2000 px photo of gravel

Load the photo. At the default settings the tile is 2400 × 1600 px. In the tiled preview, look at the centre cross: if a stone is sliced, raise Overlap to 30% so the path can go around it. If a faint darker band runs through each tile, raise Even lighting. Switch the preview to One tile to check the tile on its own, then download.

Limits

The source has to be a texture. A cut can route around detail, but it cannot invent a continuation for a horizon, a shadow of a tree, or a single plank that runs across the whole frame.

Strong directional patterns join only if both edges carry the same direction and phase. For brickwork, crop the photo to a whole number of bricks and courses first, then use a low overlap.

The tile keeps the pixels of the source. If you need a power-of-two size such as 1024 or 2048 for a game engine, resize the downloaded tile afterwards; a tile stays seamless when it is scaled.

Frequently Asked Questions

It takes a JPEG, PNG or WebP photo of a surface, such as stone, wood, fabric, grass or concrete, and returns one tile that repeats in both directions with no visible join. The download is in the same format as the file you loaded.

A strip from the right edge is laid over the left edge, and a strip from the bottom over the top, so the result loses the width of one strip in each direction. At the default 20% overlap a 2000 px photo gives a 1600 px tile. Nothing in the tile appears twice, which is what the lost strip buys.

A blend fades one edge into the other across a wide band, so both are visible at once and details turn into faint doubles. Here each pixel comes from one side or the other. The boundary between them is a path chosen to run where the two sides already look alike, softened over a few pixels.

It removes the slow change in brightness and colour across the photo: a vignette, a shadow on one side, light falling from a window. That drift is hard to see in one copy and obvious in a tiled wall, where it repeats as a grid of light and dark patches. Fine detail is left alone.

Photos shot square on to a surface with small, irregular detail work best: gravel, plaster, bark, carpet, rust. Regular patterns such as bricks or tiles only join cleanly if the crop is a whole number of repeats. A photo with strong perspective, or one large object in it, cannot be made to tile by any cut.

Yes. Download the tile, load it into the Normal Map Generator and turn on Tileable edges there, so the normals wrap across the border the same way the colour does.

Explore Our Tools

Browse all tools